Load Securement Requirements
Properly securing your cargo is one of the most critical safety requirements for commercial vehicle operators. Here is what the federal regulations actually require.
Everyone knows you need to secure your load before going down the highway. For some operators, this might just mean shutting the back doors. For others — flatbed operators, heavy haulers, and anyone carrying loose cargo — it means understanding and complying with a detailed set of federal regulations found in 49 CFR Part 393, Subpart I.
Load securement violations are one of the most common reasons commercial vehicles are placed out of service during roadside inspections. Let's break down what the regulations actually require.
Working Load Limit (WLL)
The most fundamental concept in load securement is Working Load Limit (WLL). Every tie-down device — strap, chain, binder, rope — has a WLL stamped or labeled on it. This is the maximum load the device is designed to restrain under normal working conditions.
The rule: The aggregate WLL of all tie-downs used to secure a load must be at least half the weight of the cargo being secured.
So if your load weighs 20,000 pounds, your tie-downs must have a combined WLL of at least 10,000 pounds.
How Many Tie-Downs Do You Need?
The number of tie-downs required depends on the length and weight of the cargo:
- Cargo 5 feet or less in length AND 1,100 pounds or less: 1 tie-down
- Cargo 5 feet or less in length AND more than 1,100 pounds: 2 tie-downs
- Cargo more than 5 feet but 10 feet or less: 2 tie-downs
- Cargo more than 10 feet: 2 tie-downs plus 1 additional tie-down for every 10 feet (or fraction thereof) beyond the first 10 feet
The "one every 10 feet" rule is a common shorthand, but it is not the complete picture. Always check both the length-based and WLL-based requirements and use whichever requires more tie-downs.
Direct vs. Indirect Tie-Downs
There are two methods of securing cargo:
Direct tie-down: The tie-down goes from an anchor point on the vehicle, over or through the cargo, to another anchor point. The tie-down restrains the cargo by direct contact.
Indirect tie-down (tiedown over the top): The tie-down goes from an anchor point, over the top of the cargo, and back down to another anchor point on the same side. This method uses friction and compression to hold the cargo in place.
Both methods are acceptable, but they have different WLL calculation rules. For indirect tie-downs, each tie-down only counts at half its WLL for the purpose of meeting the aggregate WLL requirement.
Chain Grades: G3 vs. G7 and Why It Matters
If you use chains for load securement, you need to know the grade of your chain. Chain grade affects its WLL significantly:
- Grade 3 (G3) chain: Lower strength, lower WLL. Often used for general purposes but has limited application in load securement.
- Grade 7 (G7) chain: Higher strength, higher WLL. This is the standard for load securement in the trucking industry.
- Grade 8 (G8) and Grade 10 (G10): Even higher strength, used for heavy-duty applications.
How to identify chain grade: Look for the number stamped on the chain links. G3 chain has no markings or a "3." G7 chain is marked with a "7" or "L." G8 chain is marked with an "8" or "V."
Using G3 chain where G7 is required means your tie-downs may not meet the aggregate WLL requirement — even if you have the right number of chains.
Common Load Securement Violations
Based on roadside inspection data, the most common load securement violations include:
- Insufficient aggregate WLL — Not enough tie-down capacity for the load weight
- Damaged or defective tie-downs — Worn, frayed, or damaged straps and chains
- Improper use of edge protection — Straps cutting over sharp edges without protection
- Missing or inadequate front-end protection — Cargo not protected against forward movement
- Improper blocking and bracing — Cargo that can shift laterally or vertically
Get It Right Before the Inspection
Load securement violations can result in an out-of-service order, meaning your vehicle cannot move until the violation is corrected. They also count against your CSA score in the Cargo-Related BASIC.
CV Safety offers load securement training that covers the federal regulations in a straightforward, practical way. We come to your location and work with your specific equipment and cargo types. Contact us to schedule a session.
Explore Topics
Written by
Jeff Byers — CV Safety
Content creator and writer sharing insights and stories.